000			04241nas a2200433 a 4500
005			20260818090613.0
008			100107s2009 th uu|m rtt 0| a1eng d
035			_a.b12071778
099		9	_aAIT Thesis no.ST-09-07
100	0		_aRitthichai Doncharee
245	1	0	_aDevelopment in manufacture and use of portland limestone cement
260			_aPathum Thani, Thailand : _bAsian Institute of Technology, _c2009
300			_a56 leaves : _bill.
490	1		_aThesis ; _vno. ST-09-07
500			_aA thesis submitted in partial fulfillment of the requirements for the degree of Master of Engineering in Structural Engineering, School of Engineering and Technology
502			_aThesis (M.Eng.) - Asian Institute of Technology, 2009
520			_aDue to global warming, the cement manufacture is one of several industries which affect to that. Therefore, the use of limestone powder as constituent material in producing cement is significantly needed in eliminating milling process. The purpose of this study is to investigate the influence of limestone powder and fineness of Portland limestone cement (PLC). Control cement and nine PLCs which used in this study were produced by inter-grinding method of clinker, limestone powder and some amount of gypsum by a ball mill of 5 kg capacity. Control cement and PLCs which are different in limestone content of 10%,20% and 30% and fineness of 3,500,4,300 and 5,000 cm²/g were obtained and tested to investigate its properties, namely physical properties of cement, mechanical properties and durability properties. In order to achieve the same consistency, the water binder ratio was kept constant at 0.45. Sand to binder ratio was 2.75. Based on the results, limestone was found can be used as a cement replacement material in order to produce PLC by inter-grinding method. In grinding process, the increase of percent replacement of limestone powder can reduced the grinding time of PLC to achieve the target fineness. Considering the cement properties, the setting time of PLC was reduced when the limestone content and fineness of PLC increased. The heat of hydration was contributed not only by increasing percent limestone replacement but also from the fineness effect of PLC. Limestone powder has more effect in the compressive strength. This is due to the filler effect of limestone powder which can improve packing of the particles and lead to increase the compressive strength. However, the increase of limestone content lead to decrease the compressive strength. In the same way, the increase of fineness of PLC the strength was also decreases. In terms of drying shrinkage the magnitude of length change of mortar containing was sharply decreased, but it then increased when the fineness of PLC increased. For the water permeability of PLC mortar, the use of Jim est one powder replacement can be reduced the water penetration as well as when the fineness of PLC increased.
650		0	_aPortland cement
650		0	_aLimestone industry
700	0		_aPennung Warnitchai, _eChairperson
700	0		_aSun Sayamipuk, _eCo-chairperson
700	0		_aThanakorn Pheeraphan, _eExamination Committee
700	0		_aRaktipong Sahamitmongkol, _eExamination committee
710	2		_aThailand (HM King), _eScholarship donor
810	2		_aAsian Institute of Technology. _tThesis ; _vno. ST-09-07
856			_3Full-Text _uhttp://203.159.5.9/ait-thesis/detail.php?q=B03975
907			_a.b12071778 _bmnait _cu
902			_a240329
998			_b0 _c100107 _dm _ea _fu _g0
945			_lmnait
945			_lmnait
945			_lmnarc
942			_c20
942			_c40
909			_aBarcode : 30050120818520 _bCREATED : 2008-10-08 _cRECORD # : i12626387 _dLPATRON : 1024295 _eLCHKIN : 2012-09-10 _f# RENEWALS : 0 _g# OVERDUE : 0 _hIUSE3 : 0 _iTOT CHKOUT : 2 _jTOT RENEW : 0
909			_aBarcode : 30050120818512 _bCREATED : 2008-10-08 _cRECORD # : i12626399 _dLPATRON : 1025405 _eLCHKIN : 2015-02-11 _f# RENEWALS : 0 _g# OVERDUE : 0 _hIUSE3 : 0 _iTOT CHKOUT : 2 _jTOT RENEW : 0
909			_aBarcode : 30050160101340 _bCREATED : 2016-04-22 _cRECORD # : i12948366 _dLPATRON : 0 _eLCHKIN : - _f# RENEWALS : 0 _g# OVERDUE : 0 _hIUSE3 : 0 _iTOT CHKOUT : 0 _jTOT RENEW : 0
999			_c28630 _d28630